Special  >  Plastic construction  >  Droplet separator  >  made of PE, insertion on top


Overview categories   Overview all products
without spraying unit  

without spraying unit


[more]
  with spraying unit  

with spraying unit


[more]
   
 




Efficient liquid separation with our plastic droplet separators - purity for your process








 

Our TA 125-2 / TA125-2-S, TA 125-2-A / TA 125-2-A-S series of droplet separators provide a high-performance solution for efficiently separating liquid components from gas and air streams. Especially when combined with air washers and gas purification systems, they are essential for reliable cleaning.

Our plastic droplet separators impress with their high corrosion resistance, ensured by the use of high-quality plastics such as PVC-U, PP, PPs, PE, and PVDF. This makes them suitable for handling aggressive gases and vapors. The impact surface separation mechanism redirects the gas flow multiple times, causing the entrained liquid droplets to collide with the profile walls due to their inertia and be separated there. The separated liquid is guided away through special phase separation chambers and grooves on the profiles.

Thanks to the sinusoidal design of the separator profiles, our droplet separators achieve high separation efficiencies of over 99% for droplets above the threshold droplet size. Despite high flow velocities, the pressure losses remain low. This enables effective separation of droplets from spray nozzles (10...100 µm) as well as ultrafine particles (below 10 µm). Our droplet separators provide a simple and cost-effective solution for pollutant separation with minimal equipment and energy requirements.

The droplet separators can be supplied for both horizontal and vertical flow configurations, consisting of a housing with the corresponding droplet separation inserts. A gas stream laden with droplets is guided through a flow grid consisting of curved and profiled lamellas. The redirection between the lamellas causes the trajectory of the droplets to deviate from the original gas flow. The separation efficiency depends on the geometry of the redirection, gas and liquid parameters, as well as the size and initial load of the droplets.

The threshold droplet plays a crucial role in the separation performance. Droplets larger than the threshold droplet size are considered to be separated 100%, while droplets smaller than the threshold are primarily separated to a lesser extent. The fractional separation efficiency allows for the assessment of a system’s separation performance.

Our droplet separators made of PVC-U, PP, PPs, PE, and PVDF offer an efficient and reliable solution for liquid separation in process engineering. Contact us for more information or to find the perfect solution for your requirements.


Optimize your shopping experience with our detailed delivery information


Plastic pipe systems


Overview of plastic pipe systems
Technical information on ABS pipe systems
Technical information on PVC  U pipe systems
Technical information on PVC  U transparent pipe systems
Technical information on PVC  C pipe systems
Technical information on PP pipe systems
Technical information on PP-R pipe systems
Technical information on PE pipe systems
Technical information on PVDF pipe systems

Chemiedur - pipe


Technical information on UP-GF (FRP) pipe systems
UP-GF (FRP) pipes
UP-GF (FRP) molded parts and connection
UP-GF-PP (FRP) molded parts and connection
UP-GF (FRP) adhesive collars
UP-GF (FRP) loose flanges
Pot Strainer DN 200 - DN 500 Inliner PP/FRP Coated
Pot Strainer DN 200 - DN 500 Inliner FRP/CBL Coated
Angle Seat Strainer DN 200 - DN 400 Inliner FRP/CBL Coated
Manhole mad of FRP and PP/FRP

Plastic pipes


Calculator for cutting pipes
Guidelines for sawing plastic pipe
Leftovers in plastic pipe
Standardization of plastic pipes and molded parts
PVC U pipes deviations
Pressure loss in pipe systems out of PVC U, PVC C and ABS pipe systems
Distinction between Rp, R and G threads
Screw lengths for flange connections

Plastic fittings


PVC U transparent ball valves
Diaphragm valves
Block valves
Butterfly valves
Plastic needle valves

 

Plastic Valves according to ATEX


New EU guideline 2014/34/EU
Plastic Valves in EX zones
Y-Strainers PP-EL DN 15 - DN 50
Check valves PP-EL DN 15 - DN 50
Angle seat valves PP-EL DN 15 - DN 50

Bonding of plastic pipes


Bonding manual
Video showing the bonding of pipes

Plastic welding


Guidelines for extrusion welding


Grids / support grids


GFK grids
Grids out of PP -el electrically conductive
Profile support grids out of PP -el electrically conductive


Molded ventilation parts


Ventilation technology


Chemical hose


PVC transparent hose with fabric inlay


Industrial tanks and chemical containers


Dosing tanks and outer containers 35 – 1000 Liter
Salt dissolving tanks 60 -5000 Liter
Storage tanks and vats
Storage tanks for water
Safety and collecting troughs
Industrial tank delivery program
Dosing tanks with agitator
Dosing tank agitators
Dosing tanks with attachments
Dosing tanks made of sheet material
Customized chemical containers
Dosing tanks with level indicators



 

IBC TANKS/CONTAINERS


IBC screw caps DN 150/DN 200
IBC adapters out of PE
IBC adapters out of PP
MULTI FLEX BLOCK for IBC BULK CONTAINER


Attachment parts for tank construction


Vapor separators
CO2 - absorbes
Manholes
Revision nozzles
Block flange

Filter housings and filter cartridges


PENTEK 3G Slime Line filter housings
PENTEK 3G Standard filter housings
PENTEK Big Blue filter housings
PENTEK PP high temperature filter housings
PENTEK PP all nature filter housings
PENTEK filter bags for Big Blue filter housings
PENTEK surface filter cartridges
PENTEK filter cartridges for depth filtration
PENTEK filter cartridges with activated carbon
CINTROPUR filter systems
CINTROPUR water filters

Flange configurator


Blind flanges, loose flanges,  rectangular flanges

Chemical resistance


Table of chemical resistance for plastic pipe systems
 

Machined plastic parts


Inserts
Screw-in parts
Threaded fittings
Screw fittings

Milled plastic parts


Loose flanges and blind flanges made of sheet material

Static mixers


Static mixers made of plastic

Strainers


Single-type and double-type strainers
Pot strainer DN 300
Angle seat strainer DN 500


Flow meters


Variable area flow meters
Configuration tool for flow meters

Filter presses


Laboratory filter presses

Injection molded parts


Scraper made of PE for filter press

Kwerk Practice Blog


The Kwerk team blogs from the field here



Partnership at the highest level.



 
         
 
 
 
 
       
 
         
 
ONLINE TOOLS
REQUEST A QUOTE
STARTING A PROJECT REQUEST