ABS Plug with BSP male thread
delivery time: 2-3 days
|
| - only suitable for plastic thread - Nominal pressure PN 10 with water at 20 °C - Temperature range -40 °C - 60 °C |
|
|
||||||||||||||||||||||||||||||
Information:
Information:
Information:
Information:
Information:
Information:
Information:
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ABS PIPES, ABS FITTINGS AND ABS VALVES - GENERAL CHARACTERISTICSAcrylonitrile - Butadiene - Styrene (ABS) is a rigid pressure piping system renowned for its high impact strength and durability which combine to give exceptional toughness. It is suitable for use over a wide temperature range from -40ºC to 80ºC at pressures up to 15 bar. ABS is especially useful at sub zero temperatures, where it retains high levels of impact strength. ABS piping is resistant to a wide range of abrasive slurries which can damage steel or other pipe materials. It is non-toxic and taint free, and is in widespread use for food products, soft drinks and high purity water. ABS pipe systems are lightweight, rigid, and easy to install. Joints are made using solvent cement, which requires no special tools. |
ABS pipe systems - Product SpecificationDURAPIPE SuperFLO ABS PIPES KIWA 49, ISO 161/1, and ISO DIS 15493 (where applicable). Pressure rating PN10 at 20°C up to 250 mm. PN8 at 20°C for 315 mm. DURAPIPE SuperFLO ABS FITTINGS KIWA 549, ISO 727 and ISO DIS 15493 (where applicable). Pressure rating PN10 at 20°C up to 250 mm. PN8 at 20°C for 315 mm. MATCHED SYSTEM The ABS products shall be from a single manufacturer to ensure complete integrity, quality and compatibility between pipes, fittings and valves. Manufacturer’s warranties may be compromised if a system is installed with materials from various manufacturers. Where this is not possible then any alternative products should be confirmed as being at least equivalent to that which is normally supplied. QUALITY SYSTEM Pipes, fittings and valves shall be manufactured in an environment which operates a Quality Assurance System assessed to ISO 9001. ENVIRONMENTAL SYSTEM The manufacturer of pipes, fittings, and valves shall be able to demonstrate compliance with applicable environmental legislation and products shall be manufactured in an environment where documented performance reviews are undertaken and an Environmental Management System is successfully assessed to ISO 14001.The manufacturer shall offer ABS solvent cements and cleaners, specially formulated to minimise any adverse effects on the environment during installation of the ABS system. THIRD PARTY APPROVALS The manufacturer shall have the following Third Party Approvals: WRAS Water Regulations Advisory Scheme 1505040 - Durapipe SuperFLO ABS Metric Pipe and Fittings 1509035 - Durapipe SuperFLO ABS VKD and VKR Ball Valves APPROVAL FOR USE IN CONTACT WITH DRINKING WATER All ABS pipes, fittings and solvent cement shall be listed in the Water Fittings and Materials Directory to show compliance with the requirements of the United Kingdom Water Regulations Advisory Service.Copies of certification of compliance with these approvals are available for inspection. MARINE APPROVALS American Bureau of Shipping Bureau Veritas Germanischer Lloyd Det Norske Veritas Lloyds register UK RINA (Royal Institution of Naval Architects) Russian Marine register DESIGN LIFE Pipes, fittings and valves shall be designed to operate continuously for 50 years at their maximum rated pressure at a working temperature of 20°C. Process Control Testing must be carried out during manufacture and documented on each and every production batch.Fittings and Pipes will be subjected to a pressure test of 3.2 x maximum recommended working pressure for 1 hour at 20°C during 1st and 2nd hours of production, then every 6 hours for fittings and 8 hours for pipes.Pipes are in addition to be impact tested after conditioning at 0°C for 1 hour.Fittings are in addition to be subject to stress relief testing at 150°C. Pipes and fittings shall undergo dimensional, marking, and visual inspection at the frequency outlined above. CHEMICAL SUITABILITY The manufacturer shall publish detailed chemical resistance data to enable the suitability of the ABS material, seals, and gaskets to be determined by designers and specifiers. The manufacturer shall also employ a qualified and experienced Chemist and provide a free-of-charge advisory service for assessing the suitability of its ABS material, seals, and gaskets. INSTALLATION SPECIFICATION The installation must be carried out by competent persons. The contractor shall be required to provide technical documentation relating to the manufacturer’s recommended Installation procedures. The manufacturer shall publish Installation recommendations, and shall also provide a free-of-charge training service for designers and installers, with appropriate written confirmation of attendance. DURAPIPE SuperFLO ABS BALL VALVES True union design, end load resistant with full pressure and shock resistant anti blow out device which conforms to design and endurance testing requirements of BS 5392 Part 1 1976, and DIN 3230 Part 3 Leak Rate One (Water and Air). The following testing will have been successfully completed: Drop Tight and Bubble Tight test Hydrostatic Shell Test 1.5 x maximum working pressure Seat Test 1.1 x maximum working pressure PRESSURE RATING 16mm to 63mm - PN 16 at 20°C (VKD series), PN10 (VXE series) 75mm to 110mm - PN16 at 20°C (VKD series) SEATS AND SEALS Seats: PTFE material fitted with O-Ring compensators Seals: Standard size O-Ring type for ease of replacement Available in EPDM or FPM materials END CONNECTIONS Plain socket ends or BSP threaded ACTUATION Options: Electric or Pneumatic DURAPIPE SuperFLO ABS DIAPHRAGM VALVES Equipped with a maintenance free hand wheel actuator with spindle extension to indicate the position of the valve open or closed. The body retaining bolts are fixed from the underside, to provide a crevice free outer surface to prevent accumulation of debris or risk of corrosion of exposed steel bolts from chemical spillage. Valves will have been hydrostatically pressure tested to the requirements of BS 5392 Part 1 1976, BS 5156, ISO 7508 and DIN 3230 Part 3 Leak Rate One. PRESSURE RATING 20mm to 110mm - PN9 at 20°C DIAPHRAGM TYPE Choice of EPDM, FPM or PTFE will be available END CONNECTION These may be plain spigot ends or flanged ACTUATION Options: Pneumatic DURAPIPE SuperFLO ABS BALL CHECK VALVES These shall be double union with plain socket or BSP threaded ends. PRESSURE RATING 20mm to 63mm - PN10 at 20°C SEALS Available in either EPDM or FPM DURAPIPE SuperFLO ABS BUTTERFLY VALVES Reinforced Polypropylene body, fully lined, with ABS disc. Full flanged design, with oval holes/inserts to suit various standard flange drillings. Lever operated, with 10 x 10° position stops, and locking device PRESSURE RATING 50mm to 250mm - PN9 at 20°C 315mm - PN 8 at 20°C PRIMARY LINER Available in EPDM, FPM, or NBR ACTUATION Electric, Pneumatic, or Gearbox (standard on sizes over 225mm) |
INFORMATION TO OUR DELIVERY PROGRAM |
OUR - PREMIUM PARTNERS - |
|
|
|
|
|
|
|
